A video can make it all so clear – allowing you to figure out a solution to a problem or inspiring you to try something new and different.
See how our tools can simplify the way you work.
-
Haas VF2 SS Roughing Aluminum w/ Garr Alumastar @ Wagner Machine Co
Some Roughing we did on our new Haas VF2 SS
1/2" Garr Tools Alumaster 3fl EM
.250" Radial DOC
.775" Axial DOC
15k RPM
250IPM -
Milling with 5/8 Garr Alumastar
Some milling we did on our new Haas VF2 SS
5/8" Garr Tools Alumaster 3fl EM
.06" Radial DOC
2.125" Axial DOC
15k RPM
100 IPM -
GARR V5 Endmill
GARR V5 Endmill -
High Speed (HSM) Pocket Clearing on Haas CNC
Using HSM to quickly and efficiently pocket out some carbon steel. Enjoy.
Material: 1018/1020 Carbon Steel, Cold Rolled, 9" Dia. Round
Operation: Profile Peel Milling (aka High Speed Milling, HSM)
Pre/Post-Processor: HSMWorks 2015
Machine/Control: 2013 Haas VF3
Tool: Garr Tool VRX 4-Flute, .500 Diameter, .020 Corner Radius
Coating: AlTiN/X.CEED (Titanium Aluminum Nitride)
Ramp Parameters: Vc = 400 SFM, Fz = .002 IPT, 4 Degree Helix
Profiling Parameters: Vc = 702 SFM, Fz = .0033 IPT, Ae=.100", Ap=.700", Constant Ae
Cooling: Cold Air -
Garr Alumastar endmill for Aluminum
3/4" 3 flute Garr Alumastar endmill running in 6061 aluminum. Run at 196 IPM, 3/4" DOC, 50 % stepover, 4000 RPM. This application is running dry for viewing however coolant is necessary. -
12mm alumastar displays @ 100 %.wmv
Garr Alumastar going at full power. Details in the video -
8Th Step Milling slots
Milling pockets, Garr 12mm Dia 3 flute solid carbide mill,
4500RPM 650mm/min, DOC 5mm/pass, coolant soluble oil 5 - 8%. -
4140 v5 cutting test
New Garr V5 cutting 4140 steel using OneCNC hsm machine strategy.
The V5 is a variable geometry 5 flute em with extra reach for aerospace materials. Details in the video. -
Garr Alumastar 3 flute carbide www.end-mills.com
Garr Alumastar 3 flute end mill cutting 6061 aluminum. 3/4" diameter at 196 IPM and 4000rpm. 3/4" doc and .300 stepover. Cat 40 taper machine, run with no coolant for demo only. You should run coolant with this tool. www.end-mills.com -
16mm VRX
GARR 16mm diameter VRX
RPM 3500
Feed 5000mm/min
AP 30mm -
High Efficiency Machining - Cal Poly SLO Formula Electric
HEM Machining of 6061-T6 Ally Billet for Cal Poly San Luis Obispo's Formula SAE Electric Racecar.
3/8" Garr Tool Long Reach Alumistar 1300 SFM, .0075 ipt, .375 DOC, 33% Stepover
Haas VF3 -
high speed machining 304L, when in doubt, push it harder and turn off the coolant!
Cutting 304L stainless steel, Garr 4fl end mill, 680sfm, .0068" chip load per flute, 5% radial engagement, no coolant!
